Turbo Charger = More Horsepower

car turbo system, hot rod turbo system, sports car turbo system, honda turbo system, corvette turbo system, race car suspension

UPP does everything from installations, to custom one off designs, to development and manufacturing of our own line of turbo systems. We have been manufacturing our own line of Turbo Systems since 2009, and even have our own line of turbochargers. No matter what your turbo project is, chances are we have you covered. So contact us today and one of our experienced technicians can help guide you as to what product/system will work best for your needs.

UPP Dyno Tuning

car turbo system, hot rod turbo system, sports car turbo system, honda turbo system, corvette turbo systemAll dyno-tuning is done in-house on our Dynocom AWD dynamometer. It is capable of measuring 1800+ wheel horse power PER AXLE with our TWIN Eddy load absorbers. These Eddy load units are two of the largest in the industry, capable of bringing a 600hp car to a dead stop at WOT. What does this mean for you? Control!!! No matter what the power, what the scenario, we can simulate it! All dynos claim to be accurate, but are they repeatable? Others claim to be the “heart-breaker”….but when is the last time you walked into a hardware store and asked for a yard stick, but demanded that it was 6” too short!!! Here at UPP, we do not mess around, we do not play games, your numbers are your numbers, and you deserve them, for better or worse. We never manipulate the dyno to make ourselves look good, nor others look bad.


Our tuner specializes in fuel injection and forced induction tuning. With our vast experience in tuning, we can tune just about any software/hardware combinations including:

-HP Tuners (GM/Ford)
-Delta Force Tuning (Ford)
-Hondata (Honda)
-Chrome (Honda)
-Neptune (Honda)
-K-Pro (Honda)
-Flash Pro (Honda)
-ECU Flash (Mitsubishi/Subaru)
-DSM Link (Mitsubishi)
-Tuner Pro (Ford/Chevy/Mitsubishi/Nissan)
-AEM Infinity
-Jet Dynamic Spectrum Tuner
-Hydra EMS
-DIY – PnP
-Power FC

-Pump Gas, C16, E85, Methanol, Meth Injection
-Nitrous: Wet, Dry, Direct Port


Because we believe in value of our customers, we believe in doing things honest and fair. Because of this when we sought tuning platforms we opted for those that did not require unnecessary hardware that you, the customer, would have to foot the cost on. We have tried to limit the use of unnecessary hardware so your hard earned money can be applied elsewhere, resulting in a faster car, and a happier customer; after all that is our #1 goal.

Because of this we have opted not to tune the following: (Usually we encourage customers to “uninstall” the hand held units from their cars and sell them, thereby offsetting the cost of the tuning)

-Cobb AP


-Base Line (3 Pulls) – $65.00
-Hourly (Min 2 hrs) – $100.00

Welcome to Under Pressure Performance

car turbo system, hot rod turbo system, sports car turbo system, honda turbo system, corvette turbo system

UNDER PRESSURE PERFORMANCE has been Colorado Springs’ premier automotive performance specialty shop for nearly a decade. From Monument to Pueblo, we provide the Pikes Peak region with a wide range of automotive services, including custom fabrication, in-house dyno tuning, engine builds, swaps and general maintenance and repair. Whether your car is 2WD or AWD, let us unleash its full potential with a dialed-in performance tune. Owner CK Field will extract every ounce of power from your turbocharged, supercharged or all-motor application, without sacrificing reliability.

We specialize in Chevrolet, Ford, Honda, Mitsubishi, Pontiac, and Subaru applications, but have the experience and expertise necessary to undertake any project, large or small. Our ASE-certified mechanics ensure all jobs are completed to the highest standard. If it’s not done right, it doesn’t leave the shop. This mentality has no doubt contributed to our continued success despite unfavorable economic conditions.

In addition to our sustaining services, we design, manufacture and market application-specific performance kits for a hassle-free way to upgrade your car for more power. Each turbo kit is hand-built and precision TIG-welded for a perfect fit and finish, every time.

Our 10,080 square-foot facility is located at 6035 Terminal Avenue, east of Powers BLVD, off Galley Road. Give us a call with any questions, or just stop by and check out the shop – we are here to help you out with whatever you need.